what gears are in my jeep

What Gears Are In My Jeep? Count the number of teeth on the pinion gear and count the number of teeth on the ring gear. Divide the ring gear teeth number by the number of teeth on the pinion. The result is your gear ratio. Note: you may need to round off the number.

How do I know what gears I have? Count the number of teeth on the pinion gear and count the number of teeth on the ring gear. Divide the ring gear teeth number by the number of teeth on the pinion. The result is your gear ratio. Note: you may need to round off the number.

Can you tell gear ratio from Vin?

The gear ratio is usually listed in the VIN code located on driver’s door, the glove box, or the ID plate on the dashboard.

What is the best gears for Jeep Wrangler?

Sounds like 4.56 or 4.88’s would be best. I normally don’t recommend 4.56 but if you have a sport with 3.73s I think 4.56 would suit your needs well. You could go 4.88 but that may be overkill. If you are stock besides the lift/tires you will be fine with 4.56s.

What is N on a Jeep?

To move back to 2H (standard driving mode), move your standard gear selector to “N” (Neutral) and allow your Jeep to slowly coast (2 to 3 miles-per-hour).

What gears are in a Jeep Rubicon?

The stock gear ratio tends to vary depending on the year and package your Jeep has. Some of the possible ratios include 3.07, 3.55, 3.73, and 4.10. Wranglers that are equipped with the Rubicon package typically come with the 4.10 gear set in their Dana 44 axles.

How do you find the gear ratio with 3 gears?

To calculate the gear ratio: Divide the number of driven gear teeth by the number of drive gear teeth. In our example, it’s 28/21 or 4 : 3. This gear ratio shows that the smaller driver gear must turn 1,3 times to get the larger driven gear to make one complete turn.

How many teeth does a 410 ring gear have?

Motive Gear D70-410 Rack and Pinion, 41-10 Teeth, 4.1 Ratio.

How do I know my rear gear ratio?

Turn the wheel TWO revolutions and count the number of driveshaft turns. The number of driveshaft rotations will help you determine your rear axle ratio. For example, if it turned 3 and a half times, it’s a 3.50:1 ratio. If it turned 4 and a quarter times, it’s a 4.25:1 ratio.

What jeeps came with a Dana 35?

The Dana 35 (as well as the AMC-15) are found in a wide variety of vehicles; the most common Dana 35 applications are as a rear axle in the Jeep Cherokee, Jeep Wrangler and Jeep Comanche. It also is a common front axle in the Ford Explorer.

What’s the difference between a Dana 35 and 44?

The ring gear on the Dana 35 measures 7.62 inches compared to the 8.5-inch ring gear on the Dana 44. That’s nearly an inch larger, which makes a world of difference especially when you’re running large tires. Interestingly enough the Dana 35 and Dana 44 share the exact same axle tubes.

Can you put 4.56 gears in a Dana 35?

Registered. I run 4.56’s in my Dana 35 for my 33’s. If you have respect for your 35, and use it within it’s limits without pushing the envelope, you should be fine keeping your 35.

What is the best gear ratio for acceleration?

Shorter gears (higher numbers) are much better suited for accelerating, such as 3.55, 3.73, 3.91’s, 4.11’s etc. Always remember, for very “give” there is a “take”. If you take lower gears to accelerate quickly from 0-60, you will give top-end speed.

What gears should I run with 35s?

If it’s an automatic, you’ll ideally want 4.56 gears. 4.10 isn’t bad at all on the highway with 35s, but 4.56 is perfect. That’s about perfect.

Should I Regear with 35s?

Yes, going to 35s you should definitely regear. And yes, the 4.10 to 4.86 is the proper range for 35s. You trade off will be fuel economy vs towing power. Being that your probably not going to be towing that much weight, you would probably be fine with the 4.10.

What does it cost to Regear a Jeep?

Depending on your type of Jeep, what you want to be done, and where you get it done, it will cost anywhere from $1,200 on the low end to $3,000 on the high end. This price range typically includes parts and labor done by a professional. What does regearing a Jeep do?

Do I drive my Jeep in 2H or N?

2h for daily driving. 4h only on dirt, gravel or snow. 4l in situations when 4h isn’t cutting it such as climbing rocks or deep sand or mud. NEVER us 4wd on dry pavement the tires must have the ability to slip.

What does 4H mean in Jeep?

In 4H (four-wheel drive, high range) all four wheels are driving your vehicle. … In 4L (four-wheel drive, low range), all four wheels are driving your vehicle and a low gear ratio is being used.

Shopping Cart
Scroll to Top